Roof ventilation: frequently asked questions
What is your lead time?
Our custom ventilation products are made in 5 days, in the size and colour of your choice.
Can you match my roof colour?
Yes. We fabricate our vents, caps and soffits from the same prepainted galvanized steel used by metal roofing manufacturers. We match the Ideal Roofing, Vicwest, MAC, Agway Metals and Color Steels palettes, and we can match a sample if your colour is not listed.
Are your vents tested?
The AirM300 and the 480 Dome were tested to CAN3-A93-M82 (R2003) by UL Canada, an ISO/IEC 17025 accredited laboratory, for wind resistance, rain, corrosion and structural integrity.
How much ventilation does an attic need?
The National Building Code of Canada generally calls for (Article 9.19.1.2) a net free ventilating area of at least 1/300 of the insulated ceiling area, more for some low-slope roofs, split between intake (soffits) and exhaust (roof vents). Always confirm with the applicable code and your roofing manufacturer’s requirements.
What is the warranty?
A limited lifetime warranty on manufacturing defects: free replacement for 10 years, then a 50% credit on a replacement part for life. Paint is covered for 10 years. The warranty transfers to the next owner and requires professional installation. See our warranty page for details.
Do you sell to resellers?
Yes. Distributors, building supply stores and dealers can resell our products, in Quebec and across Canada. See the Resellers page.
I am a roofer outside Quebec. How do I order?
Enter your region in the quote form. We will serve you directly or refer you to a reseller near you.
What is the difference between NFVA and CFM?
Net free ventilating area (NFVA) is the actual area air can pass through once screens and louvres are deducted. It is measured in square inches, and it is what the building code uses to size attic ventilation. Airflow in cubic feet per minute (CFM) is the volume of air moved: for a static vent it depends on wind and temperature difference, so our CFM figures are estimates calculated from the NFVA. To compare two vents, compare their NFVA.
How do roof vents and vented soffits work together?
Attic ventilation works like a chimney: fresh air comes in low, at the soffit, and warm, humid air leaves high, through the roof vent. Without enough intake, even the best roof vent cannot exhaust air. The net free ventilating area is therefore split between intake (vented soffits) and exhaust (roof vents).
What causes condensation in an attic?
In winter, warm, humid air from the house rises into the attic through air leaks in the ceiling. When it meets the cold roof, the moisture condenses, then freezes or drips onto the insulation. The most common causes are insufficient ventilation, blocked air intakes, an incomplete vapour barrier and bathroom or dryer fans venting into the attic. Good ventilation helps, but an airtight ceiling matters just as much.
How do I choose a vent for a metal roof?
Start with the net free ventilating area the roof needs, then pick a model that fits the pitch. On a metal roof, a vent made from the same prepainted steel as the cladding matches the colour and weathers the same way. Our roof vents are made to order for the roof’s pitch, size and colour, and installed by the roofer with the proper flashing.
What is the difference between the AirM100 and the AirM300?
Both are custom-made static roof vents. The AirM300 has the largest net free ventilating area in our range: 144 sq. in. in the 12 x 12 in. size, up to 576 sq. in. in 24 x 24 in. It was tested to CAN3-A93-M82 by UL Canada. The AirM100 is more compact: its NFVA is 70 sq. in. in the 12 x 12 in. size, limited by its side openings.
Which vent should I use on a low-slope roof?
Check the model’s pitch range. The pitch-adjustable AirM300 and AirM100 fit 1/12 to 16/12. The 480 Dome and louvered roof vents fit from 2/12, and the 2422 vent from 3/12. Below 1/12, talk to us: the AirM300 flat roof base is designed for flat roofs.
Which vent suits agricultural and commercial buildings?
For large roofs, the 480 Dome comes in 4, 6 and 8 ft lengths and was tested to CAN3-A93-M82. Gooseneck vents, louvres and louvered roof vents complete the range for ICI buildings. Livestock buildings have corrosive air: tell us how the building is used before ordering.
Can the vent match my roof colour?
Yes. Every vent is formed from the prepainted steel used by the major metal roofing manufacturers, in the exact colour of your cladding. If your colour is not in our palettes, we match it from a sample.
Where can I find installation instructions?
Our AirM300 and 480 Dome installation guides are in preparation. In the meantime, the full catalogue can be downloaded from every product page, and our technical advisors answer roofers by phone. Installation must be done by a professional roofer or contractor.